Gecko [ sachasauda.akalacademy.ac.in ]

Name	Size	Permission
ChangeLog.15.bz2	44.09 KB	-rw-r--r--
ChangeLog.16.bz2	80.2 KB	-rw-r--r--
ChangeLog.bz2	124.93 KB	-rw-r--r--
README.timezone	722 B	-rw-r--r--
README.ufc-crypt	4.46 KB	-rw-r--r--
gai.conf	2.52 KB	-rw-r--r--

Code Editor : gai.conf

# Configuration for getaddrinfo(3).
#
# So far only configuration for the destination address sorting is needed.
# RFC 3484 governs the sorting.  But the RFC also says that system
# administrators should be able to overwrite the defaults.  This can be
# achieved here.
#
# All lines have an initial identifier specifying the option followed by
# up to two values.  Information specified in this file replaces the
# default information.  Complete absence of data of one kind causes the
# appropriate default information to be used.  The supported commands include:
#
# reload  <yes|no>
#    If set to yes, each getaddrinfo(3) call will check whether this file
#    changed and if necessary reload.  This option should not really be
#    used.  There are possible runtime problems.  The default is no.
#
# label   <mask>   <value>
#    Add another rule to the RFC 3484 label table.  See section 2.1 in
#    RFC 3484.  The default is:
#
#label ::1/128       0
#label ::/0          1
#label 2002::/16     2
#label ::/96         3
#label ::ffff:0:0/96 4
#label fec0::/10     5
#label fc00::/7      6
#label 2001:0::/32   7
#
#    This default differs from the tables given in RFC 3484 by handling
#    (now obsolete) site-local IPv6 addresses and Unique Local Addresses.
#    The reason for this difference is that these addresses are never
#    NATed while IPv4 site-local addresses most probably are.  Given
#    the precedence of IPv6 over IPv4 (see below) on machines having only
#    site-local IPv4 and IPv6 addresses a lookup for a global address would
#    see the IPv6 be preferred.  The result is a long delay because the
#    site-local IPv6 addresses cannot be used while the IPv4 address is
#    (at least for the foreseeable future) NATed.  We also treat Teredo
#    tunnels special.
#
# precedence  <mask>   <value>
#    Add another rule to the RFC 3484 precedence table.  See section 2.1
#    and 10.3 in RFC 3484.  The default is:
#
#precedence  ::1/128       50
#precedence  ::/0          40
#precedence  2002::/16     30
#precedence ::/96          20
#precedence ::ffff:0:0/96  10
#
#    For sites which prefer IPv4 connections change the last line to
#
#precedence ::ffff:0:0/96  100

#
# scopev4  <mask>  <value>
#    Add another rule to the RFC 6724 scope table for IPv4 addresses.
#    By default the scope IDs described in section 3.2 in RFC 6724 are
#    used.  Changing these defaults should hardly ever be necessary.
#    The defaults are equivalent to:
#
#scopev4 ::ffff:169.254.0.0/112  2
#scopev4 ::ffff:127.0.0.0/104    2
#scopev4 ::ffff:0.0.0.0/96       14

${this.title}

Code Editor : gai.conf